This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.
If your filler cap is a standard size and has a bolt in the center then these gaskets will work.
Red 3 piece filler cap shown for demonstration purposes only.
This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
This small gasket is for the model 242, 242A, 242B, 242C, 243, 243A, 234, 234A, 247, 249 and other similar lanterns and lamps that take the smaller filler cap.
Also fits the model 500 stove and the early 520 stoves. The green filler cap is shown for identification purposes only and is not included.
This gasket is for the model 227, 427, 220/228 Slant lanterns, most winged style fuel caps, early 220B's, and other similar lanterns and lamps that have the older style cap insert.
It is the same outside diameter as the common three piece cap gasket but has a smaller inside hole.
Old part number 115-1361.
This will not seal they typical Coleman lantern cap.
This replacement screen will fit the burner caps used on 242 and 200/200A model lanterns.
This is a new brass one piece filler cap made by Coleman. Comes with a new gasket and will fit most all lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps.
It is also known as part number 425A1405.
Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.
Fits the cap number: 220C1401
Burner screen for the model 220 and 228 lanterns. Fits most double mantle lanterns and lamps with small burner caps.
This is a new Coleman made burner cap for the the 200, 200A, 202, 243, 242 and 247 lanterns. Also fits a few lamps and Sears lanterns.
Also known as part number 2423231.
This is a complete rebuild kit for the pump on an M1950 stove. You will get the cap gasket, check valve dot, fuel tube gasket and pump leather.
Cap Gasket for M1942 & M1950 stoves.
This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.
New filler cap screw for the small 242 & 249 lanterns and 500 stove size filler caps.
O rings for the Thermos lantern and stove pumps. One is for the pump, the other is for the top seal. These are for the later model Thermos lanterns and stoves where the pump and filler cap where combined.
Filler cap gasket for the Prentiss Waber lantern.
Filler plug gasket for the model CQ lamps,327 Quicklite lanterns and many older stoves. Can be used in place of the 104-136 lead gasket. Also fits the 523 military stove.
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
This is a large filler cap gasket for the Handy Gas Plants. It also works for the Tilley R1 heater.
This is the small part that attaches to the filler cap screw so you can hook the chain to it.
Burner cap and rings for the 400, 400A, 400B, 440, 442, 508, 533, & 3024 Stoves
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
This is for one used 3 piece filler cap.. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. We are showing 3 caps for demonstration purposes only to highlight the condition it could be in. This is for only one cap, not many. Comes with a new gasket that you will have to install.
New gasket for the military lantern parts well cap.
New old stock filler cap and chain for the military lantern. Will also fit any Coleman lantern or stove that used the standard size filler cap. I am 99% sure these filler caps came from the old SMP factory.
Cap gasket for Akron lanterns. Outside diameter is 5/8 of an inch. Inside diameter is 3/8 of an inch. Thickness is 1/8 inch.
Filler cap insert for the models 242, 242A, 242B, 242C, 243, 243A, 234, 234A, 247, 249 and other similar lanterns and lamps that take the smaller filler cap. Also fits the model 500 stove. Will have a new gasket installed.
Pump assembly. Comes with the neoprene pump cup and metal cap. Fits the smaller backpacking 400 series stoves and 222, 226, 229 series lanterns.
NOS burner Cap 220 Brass. Fits most models of double mantle lanterns and lamps. For nickel plated caps see part 112-3231.
This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.
New burner cap for the model 242 series lanterns. Also fits the 200, 200A, 202, 243, and 247 lanterns.
Solid brass with stainless steel screen.
This 10 pack of gaskets are for many lanterns, stoves, and lamps that take the standard 3 piece filler cap. If your filler cap is a standard size and has a bolt in the center then these gaskets will work. Red 3 piece filler cap shown for demonstration purposes only.
Brass burner cap with hex head for easy installation and removal. Fits most models of double mantle lanterns and lamps.
Solid brass with stainless steel screen.
Same part number as 112-323
Reproduction filler cap insert for the older winged style filler caps used on model 427 lanterns. Comes with the new gasket.
Rebuild kit for both the 200 and 200A lanterns. Cures most troubles.
Includes:
See Diagram in "Description" under photo at bottom left of this page
More parts for:
This is a 10 PACK for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
Steel burner cap for most models of double mantle lanterns and lamps. Has hex head for easy installation and removal.
1/2 inch long screw for the 500 stove. Requires two for the Cap and Fillers. See description tab for more details.
Universal pump assembly with a leather cup that fits almost all Coleman lanterns and stoves.
Does not fit the small Peak 1 lanterns or stoves, and also some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201
This is the short pump used on the small stoves and lanterns. 400, 440 series stoves and model 222, 226, and 229 lanterns. Comes with the plastic style pump cap and neoprene pump cup. Also known as part number 400E5203
This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket foryou to install.
This is a complete rebuild kit for the pump on an M1942 stove. You will get the cap gasket, check valve dot, and pump leather.
Rebuild kit for 502 Sportster Stove. Cures most troubles.
Includes:
See Diagram in Below
More parts for the 502 Stove HERE.
New Old Stock - Parts well cap for the military lantern. Has a new rubber gasket.
This is for one used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.
We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.
Comes with a new gasket that you will have to install.
This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.
New burner cap & screen for the model 236, 237 and 249 lanterns.
Solid brass with stainless steel screen.
Rebuild kit for models 242, 242A, 242B, and the 242C lanterns. Cures most troubles.
Includes:
See Diagram in "Description" under photo at bottom left of this page
More parts for:
Filler cap gasket for the model 523 military stove.
Chain for military lanterns and stoves. Read note below please. These are 8" long and has 15 total links, which is long enough to use on one funnel and one cap on a military lantern and have an inch left over.
NOTE: These links are slightly too big to fit in the original slots on funnels or cap clips. The first & last links will have to be modified slightly to fit. The circular part of the chain link can be bent smaller then flattened out to original the original size to fit in the cap clip - grinding them down would probably make it too weak. It will not fit into the military funnel slot - the slot would have to be enlarged in width about 1/16 of an inch to fit. No other sizes of chain are currently available that are an exact match to what was used.
This is a reproduction nickel plated brass cap for the table lamps that did not have an internal pump. Fits lamps 129, 129A, 129G, 130G, 130K, 130P. 131P, 133, 134A, 134P, 134G, 143, 150B, 150G, 150R, 150I, 150BK, 150GK, 150RK, and 150IK. Fits stoves 375, 375A, 376, 377, 378, 378A, 379, and 379A. Fits Handy Gas Plants 458 and 458G.
