- New!
Ventilator 339, Used - F150
This ventilator is used. It will fit Canadian models 339, 335, 321A, 321B, 321C, 325, and 325A.
This ventilator is used. It will fit Canadian models 339, 335, 321A, 321B, 321C, 325, and 325A.
Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-059 is needed.
Used valve wheel for the model 200A lantern. These have burn marks or other defects such as chipped edges. The wheel will still be solid and very usable, just not cosmetically very good.
This is the old style NOS red valve wheel for 200A's, 502 stoves, 220/228's and others. It is completely interchangeable with the black wheel. Newer model 200A's and model 202 took the black wheel.
This is a used part and will show signs of wear. This is the old style red valve wheel for 200A's, 502 stoves, and others. It is completely interchangeable with the black wheel.
This is a used part and will show signs of wear, sun fading, or burn marks. This is the new style red valve wheel for 200A's, 413G, 502 stoves, and others. It is completely interchangeable with the black wheel.
This is a NOS old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. May have some minor scratches from sitting around all these years.
This is a used part and may show signs of wear. There may also be a few small chips in it. This is the old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. It is the solid back style.
This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.
Reproduction valve stem nut for the model 200A lantern. Also fits the 202, 242, 243, and 247 series lanterns and also the 425F and G stoves. Does not come with the new packing.
Used valve stem for the model 200A lantern. Has been cleaned, and packing changed.
Used valve assembly for the models 242 through 242C lantern also 243 & 243A. We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.
Valve stem packing has not been changed but one will be included for you to change if needed.
This will also work on the 200A lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 200 models.
Used valve assembly for the models 242 through 242C lantern also 243 & 243A. We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.
New valve stem packing has been installed.
This will also work on the 200A lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 200 models.
Used valve assembly for 200 and 200A lanterns. In good condition. Valve stem packing has not been changed but one will be included for you to change if needed.
This will also work on the 242b & 242c lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 242 models.
This is a used newer style U tube with Venturi. These are used.
Reproduction tip cleaner assembly for the model 200, 200A, 201, 202, 242, 247, 335 and similar lanterns. Also fits the 523 and the 520/M1941 stove.
These are reproduction packings for the tip cleaner stems on many models to include these: 200, 200A, 202, 220/228, 236, 237, 242 lanterns and also many stoves. To install this packing, the lever must be straightened out, which can be difficult.
Spring Clip for 249 Preheater Cup. This is an exact reproduction. Fits well also on the 200, 202 frames also - see photos. Part also known as 235-3111
New reproduction direction disk for the 200 & 200A USA lanterns. These are aluminum and look and feel identical to the original. These are made here in the USA. Will also fit most other lanterns. They come with a protective plastic coating that can be removed before installation.
This disc refers to "mantle" as opposed to "mantles" for a double mantle lantern.
Reproduction gas tip for 200A5891 generator. Also works well for using on the 220 generators to do a kerosene conversion.
Rebuild kit for both the 200 and 200A lanterns. Cures most troubles.
Includes:
See Diagram in "Description" under photo at bottom left of this page
More parts for:
Rebuild kit for both the 200 and 200A lanterns. Cures most troubles.
Includes:
See Diagram in "Description" under photo at bottom left of this page
More parts for:
This is for a qty of one used pump screw. This is the smaller sheet metal style screw used on the 220/228D, 220/228E, and early 200A lanterns. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.
This is the smaller sheet metal style screw used on the 202, 220/228D, 220/228E, and early 200A lanterns. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.
This is a new Coleman made replacement pump cup for all lanterns that came with the rubber style.
Brand new Coleman made neoprene pump cup with a large push on nut made by Coleman. Fits pretty much all Coleman Stoves And Lanterns.
Also known as part number 6391091
Used pump clip that fits most lanterns and stoves. It is used but in fine shape.
This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
Universal pump assembly with a leather cup that fits almost all Coleman lanterns and stoves.
Does not fit the small Peak 1 lanterns or stoves, and also some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201
This is a replacement pump assembly, made by Coleman for most stoves and lanterns except for the small Peak 1 type products that have a shorter pump rod.
This pump comes with the neoprene pump cup and has parts you can exchange to match your existing type.
Used pump assembly with plastic cap, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
Used pump assembly for most stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
Used pump assembly with fixed end, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
This is a new plastic filler funnel. Small and easy to pack. Works well for standard sized filler caps. Also, the funnel tip just fits inside the smaller style caps like on the 242, 243 and some 500 stoves.
Most Popular Sized Mantles. 4 mantles per pack. Use on these lanterns models: 200, 200A 201, 214, 220, 228, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960. Also all Coleman Lamps. These Peerless mantles are the same size as the Coleman 21A mantles. Made in India.
These Peerless mantles work well on single mantle lanterns. Made in India. They are the same size as the Coleman 99 mantles. A little bigger than the 2C-HG mantles but not as big as the 111 mantles. 2 per pack.
This is a new gasket for your metal snap on parts safe. Fits the 200A size metal safe. Measures 5 1/4" from outside edge to outside edge of gasket.
Reproduction 7/16" generator wrenches. These are the wrenches used for the smaller generators. Great for putting in your part safe.
Pal nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.
Need the washers for under a 200 or 200A frame? Look HERE.