Search

Used valve Stem for the 413E, 413F, 413G, 413H, 425F, 425G, 426D, 442, 442A stoves. Also fits Sears stove models 476.72302, 476.72303, 47.74970 & 476.74980.  

You will need a P01 graphite packing for these which is HERE. Measurements:  just over 1-3/4" long and 1/4" diameter.

Please read this if you have a 425F: This has the 1/4" diameter width, not the smaller 3/16". The 425F came with both the 3/16" and the 1/4". The model 425F was a transition year, so be sure to measure your current valve stem and make sure it is 1/4".

Used 242 Valve stem.

Packings have not been changed, if you need one they are HERE

Valve stem only. Fits the 413E, 413F, 413G, 413H, 425F, 426E, 442, 442A, Sears Models 476.72303, 476.74980, 476.72302, and 476.74970. Comes with a new packing installed. Also known as part number 413A2521.

New NOS valve stem for the model 200A lantern.

Valve stem for iron.  Stem measures 2 1/8" Long

This is the gasket that goes on the 5400-5211 valve stem. It is a small flat washer. Known to fit models 5410A700, but may fit others.

This does not work on the 5430A700 or the 5430B700.

Valve stem for Quick-Lite lanterns.

These have not been serviced or cleaned and may need a new P02 packing which is HERE.

Used valve stem for the model 220/228H, J, and K lanterns. Has been cleaned and will have new graphite packing.

This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.

Reproduction valve stem nut for the model 200A lantern. Also fits the 202, 242, 243, and 247 series lanterns and also the 425F and G stoves. Does not come with the new packing.

Used valve stem nut for many Coleman lanterns.

Valve stem nut for 220, 228, 275 Lanterns. Also fits the M1942 Stove. May fit others.

N.O.S Valve stem for the model 335 and 339 lanterns.

Has a small chip on the valve wheel.

NOS valve stem with the fiber wheel for the early Coleman lamps. Will not fit lanterns. Fits model CQ, BQ, PQ, 117A, 118A, 119A lamps and others.

Valve stem for the early Coleman lamps. Will not fit lanterns. Fits model CQ, BQ, PQ, 117A, 118A, 119A lamps and others.

These are new old stock and have a bit of rust on them from sitting on a shelf for decades. Comes with a packing from the factory. Fits stoves 3F, 3H, 413B, 413C, 413D, 418, 418B, 419, 420, 371, 371A. Does not come with the needle.  If your stove has been updated to a later valve style then this would not fit.

The needle and holder for this is part number 471-2381 HERE.

A whole new valve and gen would be part number 413B6601.  That is the valve that fits the 413E and 413G stoves.

Valve stem complete for stove 393 396, 396LC, 396A, 396A-LC, and 397

Valve stem for the 425, 425B,C and E stoves

Valve stem assembly for burner 556; generator 486-262; handy gas plant 458, 458G; heater 15, 16; and stove 373.

Reproduction valve stem for the model 238B lantern.

Used valve stem for the model 200A lantern. Has been cleaned, and packing changed.

NOS valve stem for many of the older Coleman stoves. Compare your diagram with the part number 412-253 to verify it will fit. Will not fit into the 414, 424, 425, 426 series stoves.

Valve stem complete less needle for Generator 950-262

Valve stem

Valve stem for 890 series kitchen range type stoves.

Valve stem for the 220 and 228 slant lanterns. Also fits the 4A, 609 & 609A irons that use the 604-299 generator similar to the R55.

Valve stem for thermos stoves.

Used valve assembly for the models 242 through 242C lantern also 243 & 243A. We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.

Valve stem packing has not been changed but one will be included for you to change if needed.

This will also work on the 200A lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 200 models.

Used valve assembly for the models 242 through 242C lantern also 243 & 243A. We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.

New valve stem packing has been installed.

This will also work on the 200A lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 200 models.

Found on the earlier than 425F stove models. Use part 412-2531 to make a complete valve assembly.

This is a used valve assembly for the model 220/228B lanterns. It has the drain plug. Has the older style fuel and air tube. This valve has a square stem head and will not work with a more modern valve wheel. This valve was used on the 220/228B lanterns and on the early 220/228C lanterns. Packings have not been replaced. 

Used valve assembly for the model 502 stove. Valve stem packing has not been changed but one will be included for you to change if needed.

Valve minus the generator. Use part 413A6531 to make a complete valve assembly along with a graphite packing and valve stem nut. This valve body requires a valve stem that is 1/4" in size, not the smaller 3/16". Please check yours if there is any doubt about the tank/generator not being original on your stove.

P01 Graphite packing is HERE, and the valve stem nut is HERE, and the valve stem is HERE (if the parts are in stock currently).

These are Used and have a bit of rust on them. Fits stoves 3F, 3H, 413B, 413C, 413D, 418, 418B, 419, 420, 371, 371A. Does not come with the needle.  If your stove has been updated to a later valve style then this would not fit.

The needle and holder for this is part number 471-2381 HERE.

A whole new valve and gen would be part number 413B6601.  That is the valve that fits the 413E and 413G stoves.

Used valve assembly for 200 and 200A lanterns. In good condition. Valve stem packing has not been changed but one will be included for you to change if needed.

This will also work on the 242b & 242c lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 242 models.

Unknown valve stem. Has a tag on it that says it is part number 4-4005. Measures about 3 1/2 inches long.

Unknown AGM valve stem. Measures 2 1/4 inches long.

Thermos stove valve stem with orange valve wheel.

Pre Heater Stem Assembly for the Marine Stove

This is a 10 PACK. Typically used to stop a fuel leak from the valve stem on older appliances.

This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.

Made of 100% graphite.

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.

Made of 100% graphite.

Rebuild kit for models 242, 242A, 242B, and the 242C lanterns. Cures most troubles.

Includes:

• 4 Peerless string tie mantles for the 242 lanterns
• 1 Generator for the 242 lanterns
• 1 Leather replacement pump cup for the bottom of the thumb operated air pump
• 1 Valve Stem Packing for sealing fuel leaks around the fuel valve
• 1 Cap Gasket specific to the 242 - for the bottom of your fuel cap.

See Diagram in "Description" under photo at bottom left of this page

More parts for: 

• 242 HERE
• 242A HERE
• 242B HERE
• 242C HERE

Rebuild kit for 502 Sportster Stove. Cures most troubles.

Includes:

• 1 Reproduction Generator for the 502 stove lanterns
• 1 Leather replacement pump cup for the bottom of the thumb operated air pump
• 1 Valve Stem Packing for sealing fuel leaks around the fuel valve
• 2 Cap Gaskets - for the bottom of your fuel cap. 1 each of the two possible types needed

See Diagram in Below

More parts for the 502 Stove HERE. 

Rebuild kit for both the 275 and 275A lanterns. Cures most troubles.

Includes:

• 4 Peerless string tie mantles for the 275 or 275A lantern
• 1 Reproduction Generator for the 275 or 275A lantern
• 1 Leather replacement pump cup for the bottom of the thumb operated air pump
• 1 Valve Stem Packing for sealing fuel leaks around the fuel valve
• 1 Cap Gasket - for your fuel cap.

See Diagram in "Description" under photo at bottom left of this page

More parts for: 

• 275 HERE
• 275A HERE

Rebuild kit for both the 220 and 228 Coleman lanterns. Cures most troubles.

Includes:

• 4 Peerless mantles for your lantern
• 1 Reproduction generator
• 1 Leather replacement pump cup for the bottom of the thumb operated air pump
• 1 Valve Stem Packing for sealing fuel leaks around the fuel valve
• 2 Cap Gaskets - for the bottom of your fuel cap. 1 each of the two possible types needed

See Diagram in "Description" under photo at bottom left of this page

Rebuild kit for both the 200 and 200A lanterns. Cures most troubles.

Includes:

• 4 Coleman string tie mantles for the 200 or 200A lantern
• 1 Reproduction Generator for the 200 or 200A lantern
• 1 Leather replacement pump cup for the bottom of the thumb operated air pump
• 1 Valve Stem Packing for sealing fuel leaks around the fuel valve
• 2 Cap Gaskets - for the bottom of your fuel cap. 1 each of the two possible types needed

See Diagram in "Description" under photo at bottom left of this page

More parts for: 

• 200 HERE
• 200A HERE