Lanterns

These are reproduction packings for the tip cleaner stems on many models to include these: 200, 200A, 202, 220/228, 236, 237, 242 lanterns and also many stoves. To install this packing, the lever must be straightened out, which can be difficult.

Fits 282, 286, 200B lanterns

Reproduction generator spring for 200, 200A, 242, 243, 202 & Similar Sears Lanterns.

Used Part that Fits models 214, 220K, 228K, 282, 285, 286, 288, 290, & 295 lanterns. 

Will all vary in wear and some may have rust .

Same as part number 288-1251

Shorter burner tube for the model 220 slant lantern. Same as the normal 101-324 burner tube only a little shorter. Measures 2 1/4 inches long. Many of the slant 220 and 228 lanterns took shorter burner tubes.

New Old Stock - Parts well cap for the military lantern. Has a new rubber gasket.

Reproduction nickel plated vent rod for the models 234, 242A, 242B, 242C, 247, 249, and similar style lanterns. Will not fit the Australian made 249 lantern.

This is reproduction of the older style of check valve that would take the original air stem with the larger end. Excellent craftsmanship on these.

Also known as 242B5381

Reproduction spring for the fuel tube spring on the model 200, 200A, 202, 220 series, 228 series, and 242 series lanterns. Also for the 530 pocket stove and most likely many others. Overall measures 9/16" long, OD of 5/32" and an ID of approximately 1/8".

Reproduction brass generator nut for the model 530 stove. Also correct for the model 237 and 249 lanterns.

Stainless steel screw for the early style pumps. Fits many older models like the 242s, 243s, 247 and 249. These have the early type hard to find thread pattern. The original slotted pump screw has a more rounded head where these are flat.

Used long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.

This is a 10 PACK - Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

Valve assembly for Northstar Lantern.

This is a used collar for the 220E lantern. It may show signs of light rust or a little discoloration to the metal. All will vary in wear.

These came out of the old SMP factory. New pump rod for the military lantern. Would also work on a 220/228B or C. Also would work on the stoves that took a longer pump such as the model 415.

Single Ball Nut. Fits all Coleman lanterns except the 242 type models.

Reproduction cast aluminum pre-heater cup for the rare 242K lantern. Most of the 242K lanterns are missing the original pre-heater cup. If you are a purist and want to complete your 242K project then you will be very pleased with this. Looks identical to the original.

Used valve assembly for 200 and 200A lanterns. In good condition. Valve stem packing has not been changed but one will be included for you to change if needed.

This will also work on the 242b & 242c lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 242 models.

This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.

Reproduction filler plug for the old Quicklite lanterns and lamps. Made of solid brass. Now you can replace your old rounded off filler plug. Made to use the 427 gasket rather than the old lead gasket. Will come with the new gasket.

Burner assembly for the model 288 lanterns. The burner tubes are brass.

Reproduction brass pre-heater cup for the model 249 lantern.

New burner cap & screen for the model 236, 237 and 249 lanterns. 

Solid brass with stainless steel screen.

Reproduction 7/16" generator wrenches. These are the wrenches used for the smaller generators. Great for putting in your part safe.

Reproduction burner tube that measures 2 1/2 inches long. Some early lanterns and lamps took this size.

Burner tube for the Canadian model 200 lantern. It is 1 5/8 inches long which is a little shorter than the US 200A burner tube.

Rebuild kit for models 242, 242A, 242B, and the 242C lanterns. Cures most troubles.

Includes:

• 4 Peerless string tie mantles for the 242 lanterns
• 1 Generator for the 242 lanterns
• 1 Leather replacement pump cup for the bottom of the thumb operated air pump
• 1 Valve Stem Packing for sealing fuel leaks around the fuel valve
• 1 Cap Gasket specific to the 242 - for the bottom of your fuel cap.

See Diagram in "Description" under photo at bottom left of this page

More parts for: 

• 242 HERE
• 242A HERE
• 242B HERE
• 242C HERE

Steel burner tube for the 220-228 series lanterns. Measures approximately 2 7/8 inches long.

Reproduction generator nut for the Q77 generator. Same gen nut also used on the Q99 and R55 too. Also fits on iron models 4, 8 and 8A.

Fits 285, 288, 290 and 295 model lanterns. 

These are used and will vary in wear.

Reproduction valve stem bushing for the 327 and 427 Quicklite lanterns.

Nut used for the top of the valve on 214, 286, 288 and 290 models. May have other applications also.

Vent nut for the Northstar lantern.

Valve Assembly 295 Lantern

This will fit model 286A and 286B lanterns.

This is a reproduction nickel plated brass cap for the table lamps that did not have an internal pump. Fits lamps 129, 129A, 129G, 130G, 130K, 130P. 131P, 133, 134A, 134P, 134G, 143, 150B, 150G, 150R, 150I, 150BK, 150GK, 150RK, and 150IK. Fits stoves 375, 375A, 376, 377, 378, 378A, 379, and 379A. Fits Handy Gas Plants 458 and 458G.

This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves.

Has a 7/8 inch diameter and is made in the USA of oiled leather.

Used direction disk for the earlier double mantle lanterns such as 220/228B, C, D, E, and F. Will show signs of wear but still be in good condition. May be a transition disk between the 70's & 80's model lanterns.

Used ball nut. Came on the model 275 and 275A lanterns, but will fit all Coleman lanterns except the 242 type models.

This is a used collar for the 228F lantern.

Condition will vary.

Burner assembly with brass burner tubes

Used valve stem for the model 220/228H, J, and K lanterns. Has been cleaned and will have new graphite packing.

NOS metal pump cap for pump assembly. Does not come with whole assembly - just the top exterior metal cap is included.

Spring for the inside of the 236 generator.

Burner tube for the 201 kerosene lantern. Has a larger opening on the end than the 200 burner tube.

T shirt shaped piece for the valve on slant lanterns and lamps.

This is the old style NOS red valve wheel for 200A's, 502 stoves, 220/228's and others. It is completely interchangeable with the black wheel. Newer model 200A's and model 202 took the black wheel.

Used valve wheel for many of the Coleman made Sears single and double mantle lanterns.

This is a used pump square nut.

Comes with one square nut ONLY.