214
Check Valve With Stem - C001
This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date. These are the updated design that uses a smaller head on the air stem. You won't need your current air stem any more as this comes with a new one that is updated and replaces your old one.
If your part diagram calls for the 242B5381 or a 621-5361 check valve, then this would be the correct part. It is also known as part number 2006381ZCL.
- New!
Large Valve Stem Packing - P01
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
Schrader Valve Core - R510
These are new fuel rated valve cores and will fit the 214, 275, 275A, 285, 286, 288, 288A, 290, 290A lanterns and also the 400, 400A and 508 stoves.
These will function for Off/On in the following stoves, but may not allow full flame control, particularly at the low end of flame adjustment: 400B, 440, 442, 3024, 508A and 533.Need more information on the valve core? Click HERE.
Peerless Mantles 2C-HG - M01
Most Popular Sized Mantles. 4 mantles per pack. Use on these lanterns models: 200, 200A 201, 214, 220, 228, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960. Also all Coleman Lamps. These Peerless mantles are the same size as the Coleman 21A mantles. Made in India.
Peerless Mantles 24-A - M04
These Peerless mantles work well on single mantle lanterns. Made in India. They are the same size as the Coleman 99 mantles. A little bigger than the 2C-HG mantles but not as big as the 111 mantles. 2 per pack.
- Free Shipping
Filler Cap Gasket for 1 Piece Cap - S42
This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
Graphite Ribbon - P09
Graphite ribbon. It is 1/4 inch wide and 12 inches long. It is scalloped to make it more flexible for wrapping. Works for tip cleaner assemblies or any other thing where the normal graphite packing won't fit. It is easily cut with a pair of scissors to fit whatever you might need.
- Free Shipping
Large Push On Nut for Neoprene Cups - S09
Push on nut for pump. The large push on nut is used with the neoprene pump cup.
Globe 288 Amber No Logo - G04
Amber globe for the 288 size lantern. Has no manufacturer markings on it anywhere. It is approximately 4 3/8 inches tall and has a 4 1/4 inch diameter. This globe fits models 214, 214A, 214B, 214C, 282, 282A, 285, 288, 288A, 288B, 286, 286A, 286B, 321,325, 335, 5150, 5151 (A/B/C/D), 5154 (A/B), 5155 (A/B), 5159, 5417, 5419, 5428, & 5429.
Filler Cap Red Used - U801
This is a one piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.
Comes with a new gasket that you will have to install.
Filler Cap Brown Used - E1026
This is a used one piece filler cap from a 275 lantern. Paint may be chipped or missing in some spots - wear will vary. Comes with a new gasket that you will have to install.
Filler Cap 3 Piece AGM Used - E1634
Used AGM Cap. Has a steel screw and new filler cap gasket. This filler cap has the AGM hole in top. Shows signs of wear. Could be any combination of the following; wrench marks, oxidization, or fading.
Pump Assy Leather Used Push On Nut - U811
This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
Pump Assembly Plastic Cap, Used - E1426
Used pump assembly with plastic cap, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
Mantles, Insta-Clip #21, 2 pack - M12
Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack.
These simply slide on and you cross the wires instead of tying strings - very quick to install.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
Mantle Insta-Clip 2 #21 2 pack - M13
Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
Filler Cap, Black, Used - E1041
This is a used one piece filler cap. Paint is chipped or missing. Comes with a new gasket that you will have to install.
Filler Cap Steel, Used - E1386
Used steel filler cap for Coleman lanterns. All will vary in wear.
Comes with a new gasket that you will have to install.
Filler Cap Nickel, Used - E1395
Used nickel plated one piece cap. Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.
Wear and finish will vary.
Comes with a new gasket that you will have to install.
- Free Shipping
Check Valve O Ring - S20
Small thin O ring for the common Coleman check valves. Made of gas resistant material.
Pump Assembly, Universal - C045
Universal pump assembly with a leather cup that fits almost all Coleman lanterns and stoves.
Does not fit the small Peak 1 lanterns or stoves, and also some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201
- 3% less
NOS Metal Pump Cap - E1405
NOS metal pump cap for pump assembly. Does not come with whole assembly - just the top exterior metal cap is included.
Pump Assembly Neoprene Used - E1561
Used pump assembly for most stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
Spring Clip (Preheater Cup) - R579
Spring Clip for 249 Preheater Cup. This is an exact reproduction. Fits well also on the 200, 202 frames also - see photos. Part also known as 235-3111
Filler Cap Dark Green Used - E1431
This is a used one-piece filler cap that is the darker green used on 288 and similar lanterns. Paint may be chipped or scratched; each one will vary in wear. Comes with one new gasket for you to install if needed.
- Free Shipping
Filler Cap Gasket for 1 Piece Cap - 🟡𝟭𝟬 𝗣𝗔𝗖𝗞 - S42
This is a 10 PACK for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
Large Valve Stem Packing - 🟡𝟭𝟬 𝗣𝗔𝗖𝗞- P01
This is a 10 PACK - Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
Check Valve Old Style Reproduction - R577
This is reproduction of the older style of check valve that would take the original air stem with the larger end. Excellent craftsmanship on these.
Also known as 242B5381
Metal Funnel Small - R503
This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.
Globe 288 White Letter USA Original - G125
It is approximately 4 3/8 inches tall and has a 4 1/4 inch diameter. This original globe fits models 214, 214A, 214B, 214C, 282, 282A, 288, 288A, 288B, 286, 286A, 286B, 321, 335, 5150, 5151, 5152, 5153, 5154, 5155, 5158, 5159, and 5417. Made in the USA. This globe is used.
Generator Nut, Reproduction - S168
Generator nut for the model 214, 222, 229, 286, 288 290, 635 and 639 lanterns.
Filler Cap Nickel, Used - E1597
Used nickel plated one piece cap. All will vary in wear.
Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.
Comes with a new gasket that you will have to install.
Bail Wrap Protector Clear - R512
This is 12 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.
Bail Wrap Protector Black - R513
This is 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.
214 NOS Generator - E1598
This is a new, Coleman made generator for Model 214 and 214A Coleman Lanterns. Each includes new gas tip, spring, and tip cleaning wire.
These are also known as part number 3000005092.Alcohol Bottle 8 oz. - R323
This is a new 8 oz. alcohol bottle for kerosene lanterns. Typically used to fill up the pre-heater cup before lighting.
Gas Bottle, 8 oz. - R321
This is a new 8 oz. gas bottle used to fill gas lanterns, stoves and lanterns.
Check Valve Removal Tool, Universal - R701
This tool has both a wide and slim slot for almost all check valves and makes changing check valves very easy - will only take a few minutes if used properly.
C001 Check Valve: This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date.
R425 Check Valve: This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves.Air Stem, Old Style, Used - S107
Air stem older style used. Has the larger head on the end.
In the 426 stove series, this only fits 426B and C stoves, not 426 or 426A
Alcohol Bottle, 2 oz. - C020
This is a new 2 oz. alcohol bottle for kerosene lanterns. Typically used to fill up the pre-heater cup before lighting.
Feed Tube Assembly - C058
Feed Tube Assembly for the 214 Lanterns.
Also known as part number 2145231ZCL.
214 Generator - C015
This is a new, Coleman made generator for Model 214 and 214A Coleman Lanterns. Each includes new gas tip, spring, and tip cleaning wire.
These are also known as part number 3000005092.Globe 288 Clear - G03
It is approximately 4 3/8 inches tall and has a 4 1/4 inch diameter. This globe fits models 214, 214A, 214B, 214C, 282, 282A, 285, 288, 288A, 288B, 286, 286A, 286B, 321,325, 335, 5150, 5151 (A/B/C/D), 5153, 5154 (A/B), 5155 (A/B), 5159, 5417, 5419, 5428, & 5429.
Also known as part numbers 2000038026 & R214D046C.