220H

Dark Red Border Logo with "Reg.", & "Lantern". For "Some" 1971 to 1983 200A, 220, 228, 335, 236A, 237A Lanterns. This and the D11 were used interchangeably on the same lanterns/stoves. Compare with your original.

Used direction disk for the later double mantle lanterns such as 220/228, J-K. Will show signs of wear but still be in good condition. 

Used pump assembly for most stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup. 

NOS Jamb Nut for all the model 200, 242, 243, 220, and 228 models. Came from an old parts bin in a Coleman service center.

Used red carry case for models 200A, 288, 286, 290, 290A, 295, 220 F-K, 321, 327, 427 and Quick-Lite Lanterns.

Latches work great.

Used pump assembly with plastic cap, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup. 

Brass reproduction burner tube for the 220-228 series lanterns. Measures approximately 2 7/8 inches long.

This is a used one piece brass filler cap. Wear will vary. 

Comes with a new gasket that you will have to install.

New Old Stock parts. Comes with original box.

This is a used inner disc for the old 3 piece caps. May or may not have old gasket but one will be provided for you if needed. All will vary in amount of wear.

HERE is a new filler cap screw if needed.

This is an original used globe for the Coleman made Sears lanterns made from 1963 to approximately 1970. Although used, it has been inspected for damage or defects. This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. 

This is a used one-piece filler cap that is the darker green used on 288 and similar lanterns. Paint may be chipped or scratched; each one will vary in wear. Comes with one new gasket for you to install if needed.

This is an original used green sunrise logo globe made between 1946 and 1959. Although used, it has been inspected for damage or defects. 

The light green logo is very light as was common. The back has "PYREX" over "MADE IN USA"

This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. Some of the markings are very light and hard to see.

Used reflector with pistol grip for the model 220 and 228 B-F lanterns. Really good shape and solid. This hooks onto the post of the burner frame - top and bottom. See photos. Lantern not included.

This is a new plastic filler funnel. Small and easy to pack. Works well for standard sized filler caps. Also, the funnel tip just fits inside the smaller style caps like on the 242, 243 and some 500 stoves.

This is a used one piece filler cap from a 275 lantern. Paint may be chipped or missing in some spots - wear will vary. Comes with a new gasket that you will have to install.

Aftermarket product that claimed to convert your lantern to be able to run unleaded gas. It attaches to the generator. Was made to fit 286, 288, 220, 228, and 275 lanterns. It should fit a 200A too. I have never tried one and don't quite understand it but it is a neat addition to a collection.

Used AGM Cap. Has a steel screw and new filler cap gasket. This filler cap has the AGM hole in top.  Shows signs of wear. Could be any combination of the following; wrench marks, oxidization, or fading.

Used nickel plated one piece cap. All will vary in wear.

Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.  

Comes with a new gasket that you will have to install.

Used gold clamshell carry case dated 11-80 for models 275, 290, 290A, 290B, 295, 220/228 F, G, H, J, K and other similar sized lanterns. Will not fit Lanterns with the tall style vent like 220/228 B thru E, Quick-Lite or Mil-Spec Lanterns.

This product is not included in the OCP free shipping program.

Photo's with lanterns are for illustration purposes only.

This is a NOS old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. May have some minor scratches from sitting around all these years.

Made in USA 220 white logo replacement.

This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

Used made in Mexico white letter globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

This vent will fit only the 220F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on models G, H, J or K either. Please make sure the top of your 220 looks like the photo below. 

If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.

Used red sunrise globe used on Canadian lanterns. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

Fount dated 5-77 for the model 220/228 Lanterns, models H thru K. This fount has some scratches, paint chipping, and rust - see photos.

Used closed ball nut.

This ventilator is used. It will fit Canadian models 339, 335, 321A, 321B, 321C, 325, and 325A.

Used steel filler cap for Coleman lanterns. All will vary in wear.

Comes with a new gasket that you will have to install.

Used burner frame for the models 220H and 220J lanterns. 

Used burner frame for the models 220H and 220J lanterns.

This is a used fount for the 220/228K lantern dated 5-73. It has a couple paint chips and some writing on the bottom of the tank, otherwise it is in good shape.

It will work for any 220/228H through 220K type models.

Direction disk for the 220H, 220J and 220K lanterns. New old stock from an old parts bin at a repair location.

This is a used one piece filler cap. Paint is chipped or missing. Comes with a new gasket that you will have to install.

This is a Peerless Japan made globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. 

Used black carry case for models 200A, 288, 286, 290, 290A, 295, 220 F-K, 321, 327, 427 and QuickLite Lanterns.

Used filler cap that will fit most lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps. 

These are all assorted colors that have missing paint, are tarnished or have been repainted and do not match the original color - photo is for illustration purposes only - comes with one filler cap and new gasket you will have to install.

Used valve stem nut for many Coleman lanterns.

Fount dated 12-80. For models 220/228 H thru K.  Has some scuffs/scratches and paint chipping on the bottom of the fount (see photos).

Used no letter globe. This fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

New frosted sunrise logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. 

Also known as part number 2000026613.

Here is a kit of the most commonly used parts when repairing most lanterns and stoves. Buying kits saves in overall cost and comes with free shipping anywhere in the USA.

• 4 new Coleman check valves
• 10 Leather pump cups - pre-oiled
• 5 Neoprene rubber pump cups
• 10 Large valve stem packings for 1/4" 
• 5 Small valve stem packings for 3/16" 
• 10 Generator tube packings
• 10 One-piece fuel cap gaskets
• 10 Three-piece fuel cap gaskets
• 10 Cap gaskets sized for the 242 or 500 stoves
• 20 Peerless Mantles with Thorium 21A size for most double and single mantle lanterns

This is an original 220 Coleman vent. The black porcelain finish was custom done by Independence Porcelain Enamel (IPE). This is for the late 220F made after 1971 and also the G, H, K and J models. These fit on a wider burner frame, but will also fit on the early F with a smaller frame but will be a bit loose.

For those in need of a rugged, unbreakable globe, these reproduction Mica Globes fit the bill. Their built-in reflector optimizes light distribution. If needed, you can drill a hole into the reflector for easy lighting.

These made in the USA Mica Globes measure 4 7/8" x 5 1/4" and fit 206, 220, 228, 231, 236, 237, 290, 295, and QuickLite lanterns.

This is a used Century Primus globe 8936 made by Schott Suprax Glas made in West Germany. This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

Has a spot that looks glued or burnt on (see photos)

N.O.S Steel burner cap for most models of double mantle lanterns and lamps. Has hex head for easy installation and removal.

New frosted Batman globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. 

Also known as part number 2000026613.

New half frosted globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. 

Also known as part number 2000026613.

New nickel plated brass burner caps with round head. Fits most models of double mantle lantern and lamps.

Reproduction generator nut for all the model 200, 242, 243, 220, and 228 models.