220H

Here is a kit of the most commonly used parts when repairing most lanterns and stoves. Buying kits saves in overall cost and comes with free shipping anywhere in the USA.

• 4 new Coleman check valves
• 10 Leather pump cups - pre-oiled
• 5 Neoprene rubber pump cups
• 10 Large valve stem packings for 1/4" 
• 5 Small valve stem packings for 3/16" 
• 10 Generator tube packings
• 10 One-piece fuel cap gaskets
• 10 Three-piece fuel cap gaskets
• 10 Cap gaskets sized for the 242 or 500 stoves
• 20 Peerless Mantles with Thorium 21A size for most double and single mantle lanterns

This is a reproduction mica globe for the model 327 lantern. It will also fit on any lanterns that would take a 220 size globe. It is 5 1/4 inches tall. It has a diameter of approximately 4 7/8 inches. The craftsmanship is nice and it is like the old mica globes that went into the first lanterns. Has a lighting door. Mica is a mineral. It may have variations in clarity, small spots, light scratches or other natural discolorations.

This tool has both a wide and slim slot for almost all check valves and makes changing check valves very easy - will only take a few minutes if used properly.

C001 Check Valve: This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date.  
R425 Check Valve: This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves. 

This is an original 220 Coleman vent. The black porcelain finish was custom done by Independence Porcelain Enamel (IPE). This is for the late 220F made after 1971 and also the G, H, K and J models. These fit on a wider burner frame, but will also fit on the early F with a smaller frame but will be a bit loose.

This vent will fit only the 220F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on models G, H, J or K either. Please make sure the top of your 220 looks like the photo below. 

If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.

Used red sunrise globe used on Canadian lanterns. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

New frosted sunrise logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. 

Also known as part number 2000026613.

Used gold clamshell carry case dated 11-80 for models 275, 290, 290A, 290B, 295, 220/228 F, G, H, J, K and other similar sized lanterns. Will not fit Lanterns with the tall style vent like 220/228 B thru E, Quick-Lite or Mil-Spec Lanterns.

This product is not included in the OCP free shipping program.

Photo's with lanterns are for illustration purposes only.

New half frosted globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. 

Also known as part number 2000026613.

This is an original used globe for the Coleman made Sears lanterns made from 1963 to approximately 1970. Although used, it has been inspected for damage or defects. This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. 

Used reflector with pistol grip for the model 220 and 228 B-F lanterns. Really good shape and solid. This hooks onto the post of the burner frame - top and bottom. See photos. Lantern not included.

New frosted Batman globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. 

Also known as part number 2000026613.

Used red carry case for models 200A, 288, 286, 290, 290A, 295, 220 F-K, 321, 327, 427 and Quick-Lite Lanterns.

Latches work great.

This is an original used green sunrise logo globe made between 1946 and 1959. Although used, it has been inspected for damage or defects. 

The light green logo is very light as was common. The back has "PYREX" over "MADE IN USA"

This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. Some of the markings are very light and hard to see.

Used black carry case for models 200A, 288, 286, 290, 290A, 295, 220 F-K, 321, 327, 427 and QuickLite Lanterns.

New Old Stock parts. Comes with original box.

This is a used fount for the 220/228K lantern dated 5-73. It has a couple paint chips and some writing on the bottom of the tank, otherwise it is in good shape.

It will work for any 220/228H through 220K type models.

This vent will fit only the 220F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on models G, H, J or K either. Please make sure the top of your 220 looks like the photo below. 

If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.

This ventilator is used. It will fit Canadian models 339, 335, 321A, 321B, 321C, 325, and 325A.

For those in need of a rugged, unbreakable globe, these reproduction Mica Globes fit the bill. Their built-in reflector optimizes light distribution. If needed, you can drill a hole into the reflector for easy lighting.

These made in the USA Mica Globes measure 4 7/8" x 5 1/4" and fit 206, 220, 228, 231, 236, 237, 290, 295, and QuickLite lanterns.

This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves.

Has a 7/8 inch diameter and is made in the USA of oiled leather.

This is a 10 PACK - Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

Rebuild kit for both the 220 and 228 Coleman lanterns. Cures most troubles.

Includes:

• 4 Peerless mantles for your lantern
• 1 Reproduction generator
• 1 Leather replacement pump cup for the bottom of the thumb operated air pump
• 1 Valve Stem Packing for sealing fuel leaks around the fuel valve
• 2 Cap Gaskets - for the bottom of your fuel cap. 1 each of the two possible types needed

See Diagram in "Description" under photo at bottom left of this page

This is a US made original globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. These are used globes but in very nice shape.

Fount dated 12-80. For models 220/228 H thru K.  Has some scuffs/scratches and paint chipping on the bottom of the fount (see photos).

This is a used Century Primus globe 8936 made by Schott Suprax Glas made in West Germany. This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

Has a spot that looks glued or burnt on (see photos)

This is a Peerless Japan made globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. 

These mica panels are 3" x 5" in size.

General information:

• Mica can be cut with sharp scissors or a good paper cutter
• This is the only size that is available
• Mica is a natural product that is mined from the earth and will have slight variations in clarity, thickness, lines and light scratches.
• Mica is not available in amber or red.
• Mica can withstand temperatures up to 1800 degrees F.
• These are only sold in a package of 5 panels.

Used no letter globe. This fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

Fount dated 5-77 for the model 220/228 Lanterns, models H thru K. This fount has some scratches, paint chipping, and rust - see photos.

Used made in Mexico white letter globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

This is a 10 PACK of the cardboard tube that goes inside of the 200A and 220 size generators, and many others.

Made in USA 220 white logo replacement.

This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

USA made white logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

German made white logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

Reproduction generator for 220, 228, 275, and similar Sears lanterns. New generator includes new gas tip, spring, and tip cleaning wire.

Used closed ball nut.

This is the old style NOS red valve wheel for 200A's, 502 stoves, 220/228's and others. It is completely interchangeable with the black wheel. Newer model 200A's and model 202 took the black wheel.

Used valve assembly. Fits models 220H-J & 228H-J and 220K lantern. Valve packing has not been changed on these. If needed, those are HERE.

This is a NOS old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. May have some minor scratches from sitting around all these years.

This is reproduction of the older style of check valve that would take the original air stem with the larger end. Excellent craftsmanship on these.

Also known as 242B5381

Used valve wheel for many of the Coleman made Sears single and double mantle lanterns.

New Coleman made Spark Igniter. Comes in new packaging with instructions.

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

Used valve stem for the model 220/228H, J, and K lanterns. Has been cleaned and will have new graphite packing.

Used nickel plated one piece cap. Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.

Wear and finish will vary. 

Comes with a new gasket that you will have to install.

This is for one used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. 

We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.

Comes with a new gasket that you will have to install.

This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

Universal pump assembly with a leather cup that fits almost all Coleman lanterns and stoves. 

Does not fit the small Peak 1 lanterns or stoves, and also some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201