220BX
220 Burner Frame, Used - U920
Used burner frame that will fit models 220B through early 220F through approximately 1971.
220 Century Schott Suprax Globe - G50
This is a used Century Primus globe 8936 made by Schott Suprax Glas made in West Germany. This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
Has a spot that looks glued or burnt on (see photos)
220 Filler Cap Insert, Used - E1222
This is a used inner disc for the old 3 piece caps. May or may not have old gasket but one will be provided for you if needed. All will vary in amount of wear.
HERE is a new filler cap screw if needed.
- New!
220 Frosted Batman Globe - G301
New frosted Batman globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
Also known as part number 2000026613.
220 Frosted Sunrise Globe - G300
New frosted sunrise logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
Also known as part number 2000026613.
220 Globe Sears Logo - G59
This is an original used globe for the Coleman made Sears lanterns made from 1963 to approximately 1970. Although used, it has been inspected for damage or defects. This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
220 Globe WL Mexico - G106
Used made in Mexico white letter globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
220 Globe White Letter Germany - G05
German made white logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
220 Globe, Pyrex Green Sunrise Logo - G24
This is an original used green sunrise logo globe made between 1946 and 1959. Although used, it has been inspected for damage or defects.
The light green logo is very light as was common. The back has "PYREX" over "MADE IN USA"
This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. Some of the markings are very light and hard to see.
220 Half Frosted Globe - G302
New half frosted globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
Also known as part number 2000026613.
220 No Letter Globe - G179
Used no letter globe. This fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
- New!
220 Old Style Vent, Used - U862
This is a used ventilator for the model 220B through 220E lantern.
This vent has a few paint chippings. (see photos)
220 Old Style Vent, Used - U863
This is a used ventilator for the model 220B through 220E lantern.
Has some paint chips and scratches (see photos)
220 Peerless Globe - G130
This is a Peerless Japan made globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
220 Red Logo Pyrex Globe USA - G28
This is a US made original globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. These are used globes but in very nice shape.
220 White Logo USA Globe - G44
USA made white logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
220/228 Air Tube Screw Phillips - S74
Screw for tip cleaner assembly to air intake tube. Phillips head screwdriver type used on later 220/228 models.
220/228 Eccentric Block, Used - S119
Used Eccentric Block for the 220 & 228 lanterns up through model F. Will not fit H, J, or K.
220/228 Valve Bushing Set - S134
This is the set of bushings used on both sides of the graphite packing on the valve stem of the 220/228B through 220/228K lanterns.
- Free Shipping
252 Direction Disk - S10
Direction disk for the military lanterns. These came out of the old SMP factory.
327 Mica Globe - G09
This is a reproduction mica globe for the model 327 lantern. It will also fit on any lanterns that would take a 220 size globe. It is 5 1/4 inches tall. It has a diameter of approximately 4 7/8 inches. The craftsmanship is nice and it is like the old mica globes that went into the first lanterns. Has a lighting door. Mica is a mineral. It may have variations in clarity, small spots, light scratches or other natural discolorations.
Air Intake Tube Old Steel - E1138
This is a old timey steel tube made back in WWII and would have been used on the 220C model lanterns.
Air Stem Long New Style - E1048
Reproduction long air stem with newer style screw end. Same length as the 216-532 air stem. Allows the use of the new style check valve with the smaller threaded end for stoves that took a longer air stem. Overall length is 5.5".
Air Stem Old Style Long Used - E1613
Used long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.
Air Stem, Old Style, Long, Reproduction - R582
NOS long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.
Air Stem, Old Style, Used - S107
Air stem older style used. Has the larger head on the end.
In the 426 stove series, this only fits 426B and C stoves, not 426 or 426A
Air Tube Screw - S72
Screw for tip cleaner assembly to air intake tube. Flat head screwdriver type used on earlier 220/228 models.
- Free Shipping
Bail Cotter Pin, New - E1150
New cotter pin for the 220B, 235 and other early style bails. This tiny cotter pin may be a little long and will have to be trimmed, but the width is correct to pass through the bail holes.
Bail Wrap Protector Black - R513
This is 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.
Bail Wrap Protector Clear - R512
This is 12 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.
Ball Nut, 2 Pack - C011
These are a new Coleman made 2 pack of ball nuts. This is the common sized ball nut used on most Coleman lanterns.
Also known as part number 3000005384.Black Valve Wheel New Style, Used - S112
This is a used part and may show signs of wear or have a few chips in it. This is the new style black valve wheel for 200A's, models 220H, 220J and 220K, 228F and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. The main difference is the hollow style back. In the 426 stove series, this only fits 426 or 426A
Burner Assembly Complete, Used - U831
This is a used burner assembly that will fit models 220/228B through 220/228E. It will show signs of use but will be in good condition. Has the long vent rod for the taller vents. If you change the vent rod to a shorter one, (HERE) it would work fine for a 220F.
Burner Cap 220 Brass Hex - S32
Brass burner cap with hex head for easy installation and removal. Fits most models of double mantle lanterns and lamps.
Solid brass with stainless steel screen.
Same part number as 112-323
Burner Cap 220 Brass Round, NOS - E1044
NOS burner Cap 220 Brass. Fits most models of double mantle lanterns and lamps. For nickel plated caps see part 112-3231.
Burner Cap 220 Steel Hex - E1267
Steel burner cap for most models of double mantle lanterns and lamps. Has hex head for easy installation and removal.
Burner Tube - R319
Brass reproduction burner tube for the 220-228 series lanterns. Measures approximately 2 7/8 inches long.
Burner Tube 2 1/2 Inch - E1471
Reproduction burner tube that measures 2 1/2 inches long. Some early lanterns and lamps took this size.
Burner Tube Brass 2 3/4 - E1129
Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 3/4 inches long.
Burner Tube Brass 2 7/8 - E1254
Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long.
Burner Tube Short/Slant - S135
Shorter burner tube for the model 220 slant lantern. Same as the normal 101-324 burner tube only a little shorter. Measures 2 1/4 inches long. Many of the slant 220 and 228 lanterns took shorter burner tubes.
Burner Tube Steel - E1480
Steel burner tube for the 220-228 series lanterns. Measures approximately 2 7/8 inches long.
Burner Tube Steel Old Style - E1101
Steel burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long. These are the older style gray looking steel tubes as used on lanterns and lamps made during the war years.
Check Valve Old Style - R425
Reproduction check valve. This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves.
Coleman Filter Funnel - C024
New Filter Funnel For Lamps And Stoves.
Stops filling your lantern or stove at the correct level.
- Free Shipping
Direction Disk Double Mantle, Used - S109
Used direction disk for the earlier double mantle lanterns such as 220/228B, C, D, E, and F. Will show signs of wear but still be in good condition. May be a transition disk between the 70's & 80's model lanterns.
Eccentric Block - E1039
New reproduction eccentric Block for the 275, 235, 220/228 C, D, E and F models in addition to some lamps.
- Free Shipping
Filler Cap Gasket for 1 Piece Cap - S42
This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361