228B

Shorter burner tube for the model 220 slant lantern. Same as the normal 101-324 burner tube only a little shorter. Measures 2 1/4 inches long. Many of the slant 220 and 228 lanterns took shorter burner tubes.

Reproduction spring for the fuel tube spring on the model 200, 200A, 202, 220 series, 228 series, and 242 series lanterns. Also for the 530 pocket stove and most likely many others. Overall measures 9/16" long, OD of 5/32" and an ID of approximately 1/8".

This is a 10 PACK - Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

Used long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.

Reproduction burner tube that measures 2 1/2 inches long. Some early lanterns and lamps took this size.

Reproduction 7/16" generator wrenches. These are the wrenches used for the smaller generators. Great for putting in your part safe.

Steel burner tube for the 220-228 series lanterns. Measures approximately 2 7/8 inches long.

Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves.

Has a 7/8 inch diameter and is made in the USA of oiled leather.

Used direction disk for the earlier double mantle lanterns such as 220/228B, C, D, E, and F. Will show signs of wear but still be in good condition. May be a transition disk between the 70's & 80's model lanterns.

This is a used pump square nut.

Comes with one square nut ONLY.

This is the old style NOS red valve wheel for 200A's, 502 stoves, 220/228's and others. It is completely interchangeable with the black wheel. Newer model 200A's and model 202 took the black wheel.

This is a used burner assembly that will fit models 220/228B through 220/228E. It will show signs of use but will be in good condition. Has the long vent rod for the taller vents. If you change the vent rod to a shorter one, (HERE) it would work fine for a 220F.

These are from used generators - they are straight with no gas tip or pricker rod inside. They will most likely need to be cleaned to be used. The interior may be clear, or it may have remnants of old internal packing/springs.

Valve stem nut for 220, 228, 275 Lanterns. Also fits the M1942 Stove. May fit others.

New nickel plated brass burner caps with hex head. Fits most models of double mantle lantern and lamps.

These mica panels are 3" x 5" in size.

General information:

• Mica can be cut with sharp scissors or a good paper cutter
• This is the only size that is available
• Mica is a natural product that is mined from the earth and will have slight variations in clarity, thickness, lines and light scratches.
• Mica is not available in amber or red.
• Mica can withstand temperatures up to 1800 degrees F.
• These are only sold in a package of 5 panels.

Fuel tip used on the end of the fuel tubes of early 220/228B lanterns, 236 and some lamps.

This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.

This is a used pump assembly for the model 220C. It has a thick steel knurled pump cap rather than brass. The steel cap was usually found on the models 220/228C made during the war years. It would also fit the 427, 228B, 235, 220BX, 220B, and 228C lanterns. It would fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. This is a used pump assembly. It has a new pump leather installed. It may show signs of wear and surface rust. Could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style labeled "Thick" with the thicker knurled portion which is 5/16" thick.

This is a used pump assembly for the model 220b. It would also be correct for the 427, 228B, 235, 220BX, 220C, and 228C lanterns. It would also fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B.  It has been cleaned and has a new pump leather installed. It may show signs of wear and could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style one labeled "Thin" with the thinner knurled portion which is 1/4" thick. Has a nickel plated brass cap.

Used Pump Assembly Spring

Spring ONLY

This is a used vent for models 227 and 228B through 228E. Very nice vent. Has a small dent/rust where the ball nut sits (see photos).

This is a used valve assembly for the model 220/228B lanterns. It has the drain plug. Has the older style fuel and air tube. This valve has a square stem head and will not work with a more modern valve wheel. This valve was used on the 220/228B lanterns and on the early 220/228C lanterns. Packings have not been replaced. 

Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 3/4 inches long.

These are NOS Coleman ball nuts

Reproduction eccentric block for the very early 220B lantern that took the longer eccentric. Will not work in the later 220B or other 220 series lantern.

Early mixing chamber used on the early 220/228B lanterns and lamps of the same period.

Steel burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long. These are the older style gray looking steel tubes as used on lanterns and lamps made during the war years.

These screws are for lanterns requiring a slightly larger and longer fastener than typically found on a 200 lantern. These fit the 236, 237, 220B, and many other older lanterns. Size is 4-40 x 5/16".

Rebuild kit for both the 220 and 228 Coleman lanterns. Cures most troubles.

Includes:

• 4 Peerless mantles for your lantern
• 1 Reproduction generator
• 1 Leather replacement pump cup for the bottom of the thumb operated air pump
• 1 Valve Stem Packing for sealing fuel leaks around the fuel valve
• 2 Cap Gaskets - for the bottom of your fuel cap. 1 each of the two possible types needed

See Diagram in "Description" under photo at bottom left of this page

Used pump assembly for most stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup. 

NOS Jamb Nut for all the model 200, 242, 243, 220, and 228 models. Came from an old parts bin in a Coleman service center.

Used pump assembly with plastic cap, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup. 

Used Needle for the fuel and air tube inside the fount. Used on 220 and 228 series lanterns up thru model F and the 118B lamp.

Brass reproduction burner tube for the 220-228 series lanterns. Measures approximately 2 7/8 inches long.

New Old Stock parts. Comes with original box.

This is a used inner disc for the old 3 piece caps. May or may not have old gasket but one will be provided for you if needed. All will vary in amount of wear.

HERE is a new filler cap screw if needed.

Used reflector with pistol grip for the model 220 and 228 B-F lanterns. Really good shape and solid. This hooks onto the post of the burner frame - top and bottom. See photos. Lantern not included.

This is a new plastic filler funnel. Small and easy to pack. Works well for standard sized filler caps. Also, the funnel tip just fits inside the smaller style caps like on the 242, 243 and some 500 stoves.

Aftermarket product that claimed to convert your lantern to be able to run unleaded gas. It attaches to the generator. Was made to fit 286, 288, 220, 228, and 275 lanterns. It should fit a 200A too. I have never tried one and don't quite understand it but it is a neat addition to a collection.

This is a used vent for models 227 and 228B through 228E. Very nice. Has a couple small paint chips (see photos).

This is a NOS old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. May have some minor scratches from sitting around all these years.

This is an early style 228 ventilator. This vent has a couple paint chips and small white dots that might come out but is otherwise in great condition (see photos)

Used guillotine carry case for all large hat 228 style lanterns. Will also fit 220, 275, 290, and 295. 

Latch works great - has some scratches and a couple small dents - overall great condition (see photos)

This product is not included in the OCP free shipping program.

Early mixing chamber used on the early 220/228B lanterns and lamps of the same period.

Aluminum mixing chamber for most double mantle lanterns and lamps. Coleman experimented with aluminum for a few parts back in the old days. I believe it was discovered that aluminum could not hold up to the heat. Probably more of a display piece than for using.

Used valve stem nut for many Coleman lanterns.

NOS long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.

Here is a kit of the most commonly used parts when repairing most lanterns and stoves. Buying kits saves in overall cost and comes with free shipping anywhere in the USA.

• 4 new Coleman check valves
• 10 Leather pump cups - pre-oiled
• 5 Neoprene rubber pump cups
• 10 Large valve stem packings for 1/4" 
• 5 Small valve stem packings for 3/16" 
• 10 Generator tube packings
• 10 One-piece fuel cap gaskets
• 10 Three-piece fuel cap gaskets
• 10 Cap gaskets sized for the 242 or 500 stoves
• 20 Peerless Mantles with Thorium 21A size for most double and single mantle lanterns