228B

Burner screen for the model 220 and 228 lanterns. Fits most double mantle lanterns and lamps with small burner caps.

This is a used inner disc for the old 3 piece caps. May or may not have old gasket but one will be provided for you if needed. All will vary in amount of wear.

HERE is a new filler cap screw if needed.

Used reflector with pistol grip for the model 220 and 228 B-F lanterns. Really good shape and solid. This hooks onto the post of the burner frame - top and bottom. See photos. Lantern not included.

Screw for tip cleaner assembly to air intake tube. Phillips head screwdriver type used on later 220/228 models.

This is the set of bushings used on both sides of the graphite packing on the valve stem of the 220/228B through 220/228K lanterns.

This is a used vent for models 227 and 228B through 228E. Very nice vent. Has a small dent/rust where the ball nut sits (see photos).

This is a used vent for models 227 and 228B through 228E. Very nice. Has a couple small paint chips (see photos).

This is an early style 228 ventilator. This vent has a couple paint chips and small white dots that might come out but is otherwise in great condition (see photos)

Direction disk for the military lanterns. These came out of the old SMP factory.

Used long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.

NOS long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.

Air stem older style used. Has the larger head on the end.

In the 426 stove series, this only fits 426B and C stoves, not 426 or 426A

Screw for tip cleaner assembly to air intake tube. Flat head screwdriver type used on earlier 220/228 models.

This is 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.

This is 12 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.

These are a new Coleman made 2 pack of ball nuts. This is the common sized ball nut used on most Coleman lanterns.
Also known as part number 3000005384.

These are NOS Coleman ball nuts

This is a used part and may show signs of wear or have a few chips in it. This is the new style black valve wheel for 200A's, models 220H, 220J and 220K, 228F and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. The main difference is the hollow style back. In the 426 stove series, this only fits 426 or 426A

This is a used burner assembly that will fit models 220/228B through 220/228E. It will show signs of use but will be in good condition. Has the long vent rod for the taller vents. If you change the vent rod to a shorter one, (HERE) it would work fine for a 220F.

Brass burner cap with hex head for easy installation and removal. Fits most models of double mantle lanterns and lamps.

Solid brass with stainless steel screen.

Same part number as 112-323

New nickel plated brass burner caps with hex head. Fits most models of double mantle lantern and lamps.

Steel burner cap for most models of double mantle lanterns and lamps. Has hex head for easy installation and removal.

Brass reproduction burner tube for the 220-228 series lanterns. Measures approximately 2 7/8 inches long.

Reproduction burner tube that measures 2 1/2 inches long. Some early lanterns and lamps took this size.

Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 3/4 inches long.

Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long.

Shorter burner tube for the model 220 slant lantern. Same as the normal 101-324 burner tube only a little shorter. Measures 2 1/4 inches long. Many of the slant 220 and 228 lanterns took shorter burner tubes.

Steel burner tube for the 220-228 series lanterns. Measures approximately 2 7/8 inches long.

Steel burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long. These are the older style gray looking steel tubes as used on lanterns and lamps made during the war years.

Reproduction check valve for the military lanterns. Will also fit the models 220/228B and 220/228C. Will not fit the later style lanterns.

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

Reproduction check valve. This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves.

New Filter Funnel For Lamps And Stoves. 

Stops filling your lantern or stove at the correct level.

New Old Stock parts. Comes with original box.

Used direction disk for the earlier double mantle lanterns such as 220/228B, C, D, E, and F. Will show signs of wear but still be in good condition. May be a transition disk between the 70's & 80's model lanterns.

Reproduction eccentric block for the very early 220B lantern that took the longer eccentric. Will not work in the later 220B or other 220 series lantern.

This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap. 

If your filler cap is a standard size and has a bolt in the center then these gaskets will work. 

Red 3 piece filler cap shown for demonstration purposes only.

This 10 pack of gaskets are for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.  If your filler cap is a standard size and has a bolt in the center then these gaskets will work. Red 3 piece filler cap shown for demonstration purposes only.

This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.

Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.

Fits the cap number: 220C1401

Fuel tip used on the end of the fuel tubes of early 220/228B lanterns, 236 and some lamps.

Reproduction spring for the fuel tube spring on the model 200, 200A, 202, 220 series, 228 series, and 242 series lanterns. Also for the 530 pocket stove and most likely many others. Overall measures 9/16" long, OD of 5/32" and an ID of approximately 1/8".

New steel fuel tube spring for the models 200, 200A, 202, 220 series, 228 series, and 242 series lanterns. Also for the 530 pocket stove and most likely many others. Overall measures 9/16" long, OD of 3/16" and an ID of approximately 1/8".

Used Needle for the fuel and air tube inside the fount. Used on 220 and 228 series lanterns up thru model F and the 118B lamp.

Fuel and air tube for lantern models 220/228B, 220BX, and 220/228C. Earliest style of fuel and air tube. 

Here is a kit of the most commonly used parts when repairing most lanterns and stoves. Buying kits saves in overall cost and comes with free shipping anywhere in the USA.

• 4 new Coleman check valves
• 10 Leather pump cups - pre-oiled
• 5 Neoprene rubber pump cups
• 10 Large valve stem packings for 1/4" 
• 5 Small valve stem packings for 3/16" 
• 10 Generator tube packings
• 10 One-piece fuel cap gaskets
• 10 Three-piece fuel cap gaskets
• 10 Cap gaskets sized for the 242 or 500 stoves
• 20 Peerless Mantles with Thorium 21A size for most double and single mantle lanterns

Reproduction generator for 220, 228, 275, and similar Sears lanterns. New generator includes new gas tip, spring, and tip cleaning wire.

Reproduction generator nut for all the model 200, 242, 243, 220, and 228 models.

Used generator nut for all the model 200, 242, 243, 220, and 228 models. It is in fine shape, just dirty.

Reproduction generator spring for 200, 200A, 220, 228, 242, 243, 202 & Similar Sears Lanterns.