228B
Wrench 220B - R300
Wrench for the lantern models 220/228B through 220/228F. Fits the small nut at the bottom of the burner frame. Angled to fit that hard to get at nut. It is a 9/16 wrench.
Valve Wheel Screw - S60
These screws are for lanterns requiring a slightly larger and longer fastener than typically found on a 200 lantern. These fit the 236, 237, 220B, and many other older lanterns. Size is 4-40 x 5/16".
Valve Wheel Red, Old Style, NOS - E1401
This is the old style NOS red valve wheel for 200A's, 502 stoves, 220/228's and others. It is completely interchangeable with the black wheel. Newer model 200A's and model 202 took the black wheel.
Valve Wheel Black, Old Style, NOS - E1679
This is a NOS old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. May have some minor scratches from sitting around all these years.
Valve Wheel Black Old Style, Used - S113
This is a used part and may show signs of wear. There may also be a few small chips in it. This is the old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. It is the solid back style.
Valve Stem Retaining Ring - 1/4" - S04
This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.
Valve Stem Nut - S152
Valve stem nut for 220, 228, 275 Lanterns. Also fits the M1942 Stove. May fit others.
Valve Assembly Old B Style Used - E1285
This is a used valve assembly for the model 220/228B lanterns. It has the drain plug. Has the older style fuel and air tube. This valve has a square stem head and will not work with a more modern valve wheel. This valve was used on the 220/228B lanterns and on the early 220/228C lanterns. Packings have not been replaced.
- 3% less
Used Generator Body - E1478
These are from used generators - they are straight with no gas tip or pricker rod inside. They will most likely need to be cleaned to be used. The interior may be clear, or it may have remnants of old internal packing/springs.
- Free Shipping
Two Mantle Direction Disk USA Reproduction - S02
New reproduction direction disk for the many of the 2 mantle lanterns made in the USA like the 220 and 228 models B thru F. These are aluminum and look and feel identical to the original, and they are made here in the USA. They come with a protective plastic coating that can be removed before installation.
This disc refers to "mantles" as opposed to "mantle" for a single mantle lantern.
Tip Cleaner Stem Reproduction - R700
This is a reproduction tip cleaner stem for the model 220/228B through 220/228F lantern. Looks a little different that the original but is a great lower cost alternative to the original ones.
This also fits the AGM 2572 & Kamplite RL-3
- New!
Tip Cleaner & Air Piece Assembly, Nickel - E1249
Nickel Tip Cleaner Assembly with air piece. Does not have the eccentric block.
- New!
Smith-Victor Large Carry Case - CC15
Used Smith-Victor carry case for all large hat 228 style lanterns. Will also fit 220, 252, 275, 290, and 295.
Has some scratches, one edge is bent a little but doesn't hinder the case closing, both latches aren't perfect on latches tight but is a little bent, the other latch is loose but still closes.
This product is not included in the OCP free shipping program.
Rebuild Kit - 220 & 228 Lanterns - K16
Rebuild kit for both the 220 and 228 Coleman lanterns. Cures most troubles.
Includes:
- 4 Peerless mantles for your lantern
- 1 Reproduction generator
- 1 Leather replacement pump cup for the bottom of the thumb operated air pump
- 1 Valve Stem Packing for sealing fuel leaks around the fuel valve
- 2 Cap Gaskets - for the bottom of your fuel cap. 1 each of the two possible types needed
See Diagram in "Description" under photo at bottom left of this page
Pump Assembly, Universal - C045
Universal pump assembly with a leather cup that fits almost all Coleman lanterns and stoves.
Does not fit the small Peak 1 lanterns or stoves, and also some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201
Pump Assembly, Universal - C006
This is a replacement pump assembly, made by Coleman for most stoves and lanterns except for the small Peak 1 type products that have a shorter pump rod.
This pump comes with the neoprene pump cup and has parts you can exchange to match your existing type.Pump Assembly, 220C Thick Steel Cap, Used - E1296
This is a used pump assembly for the model 220C. It has a thick steel knurled pump cap rather than brass. The steel cap was usually found on the models 220/228C made during the war years. It would also fit the 427, 228B, 235, 220BX, 220B, and 228C lanterns. It would fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. This is a used pump assembly. It has a new pump leather installed. It may show signs of wear and surface rust. Could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style labeled "Thick" with the thicker knurled portion which is 5/16" thick.
- New!
Pump Assembly, 220B Thin Brass Cap, Used - E1054
This is a used pump assembly for the model 220b. It would also be correct for the 427, 228B, 235, 220BX, 220C, and 228C lanterns. It would also fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. It has been cleaned and has a new pump leather installed. It may show signs of wear and could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style one labeled "Thin" with the thinner knurled portion which is 1/4" thick. Has a nickel plated brass cap.
Pump Assembly Plastic Cap, Used - E1426
Used pump assembly with plastic cap, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
Pump Assembly Neoprene Used - E1561
Used pump assembly for most stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
Pump Assembly Leather Used Square Nut - U810
This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
Plastic Funnel Small - R702
This is a new plastic filler funnel. Small and easy to pack. Works well for standard sized filler caps. Also, the funnel tip just fits inside the smaller style caps like on the 242, 243 and some 500 stoves.
Peerless Mantles 2C-HG - M01
Most Popular Sized Mantles. 4 mantles per pack. Use on these lanterns models: 200, 200A 201, 214, 220, 228, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960. Also all Coleman Lamps. These Peerless mantles are the same size as the Coleman 21A mantles. Made in India.
Peerless Mantles 24-A - M04
These Peerless mantles work well on single mantle lanterns. Made in India. They are the same size as the Coleman 99 mantles. A little bigger than the 2C-HG mantles but not as big as the 111 mantles. 2 per pack.
Parts Safe Gasket 220 - E1446
This is a new gasket for your metal snap on parts safe. Fits the 220 size metal safe.
Part Safe Wrench Reproduction - R551
Reproduction 7/16" generator wrenches. These are the wrenches used for the smaller generators. Great for putting in your part safe.
NOS Burner Cap 220 Nickel Round - E1631
New nickel plated brass burner caps with round head. Fits most models of double mantle lantern and lamps.
N.O.S Burner Cap 220 Steel Hex - E1663
N.O.S Steel burner cap for most models of double mantle lanterns and lamps. Has hex head for easy installation and removal.
- New!
Mixing Chamber Used, with Vent Rod - E1367
Early mixing chamber used on the early 220/228B lanterns and lamps of the same period.
- New!
Mixing Chamber Earlier Style, Used - E1636
Early mixing chamber used on the early 220/228B lanterns and lamps of the same period.
Mixing Chamber Aluminum - E1568
Aluminum mixing chamber for most double mantle lanterns and lamps. Coleman experimented with aluminum for a few parts back in the old days. I believe it was discovered that aluminum could not hold up to the heat. Probably more of a display piece than for using.
Mica Globe Panels - E1120
These mica panels are 3" x 5" in size.
General information:
- Mica can be cut with sharp scissors or a good paper cutter
- This is the only size that is available
- Mica is a natural product that is mined from the earth and will have slight variations in clarity, thickness, lines and light scratches.
- Mica is not available in amber or red.
- Mica can withstand temperatures up to 1800 degrees F.
- These are only sold in a package of 5 panels.
Metal Funnel Small - R503
This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.
Mantles, Insta-Clip #21, 2 pack - M12
Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack.
These simply slide on and you cross the wires instead of tying strings - very quick to install.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
Mantle String Tie #21 4 Pack - M02
Coleman's Most Popular Sized Mantles. 4 mantles per pack.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
Also known as part number 3000004344.
Mantle String Tie #21 2 pack - M03
Coleman's Most Popular Sized Mantles. 2 mantles per pack.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
Also known as part number 3000004345.
Mantle Insta-Clip 2 #21 2 pack - M13
Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
Leather Pump Cup Kit - C005
This is a new leather pump cup, push on nut and back-up plate. This will fit most all lanterns and stoves. If converting from a rubber pump cup, make sure you use the new back up plate in this kit.
Also known as part number 3000005094.
Leather Pump Cup - 🟡𝟭𝟬 𝗣𝗔𝗖𝗞 - S81
This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
Leather Pump Cup - S81
This is the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
Large Valve Stem Packing - 🟡𝟭𝟬 𝗣𝗔𝗖𝗞- P01
This is a 10 PACK - Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
- New!
Large Valve Stem Packing - P01
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
- New!
Lantern Fuel Converter - E1570
Aftermarket product that claimed to convert your lantern to be able to run unleaded gas. It attaches to the generator. Was made to fit 286, 288, 220, 228, and 275 lanterns. It should fit a 200A too. I have never tried one and don't quite understand it but it is a neat addition to a collection.