228E
- New!
Lantern Fuel Converter - E1570
Aftermarket product that claimed to convert your lantern to be able to run unleaded gas. It attaches to the generator. Was made to fit 286, 288, 220, 228, and 275 lanterns. It should fit a 200A too. I have never tried one and don't quite understand it but it is a neat addition to a collection.
- New!
220-228 Coleman Lantern Reflector - LR1
Used reflector with pistol grip for the model 220 and 228 B-F lanterns. Really good shape and solid. This hooks onto the post of the burner frame - top and bottom. See photos. Lantern not included.
- New!
Filler Cap 3 Piece Brass, Used - E1156
This is for one used 3 piece filler cap.. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. We are showing 3 caps for demonstration purposes only to highlight the condition it could be in. This is for only one cap, not many. Comes with a new gasket that you will have to install.
- New!
Large Valve Stem Packing - P01
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
- New!
Tip Cleaner & Air Piece Assembly, Nickel - E1249
Nickel Tip Cleaner Assembly with air piece. Does not have the eccentric block.
- New!
Guillotine 228 Carry Case - CC2
Used guillotine carry case for all large hat 228 style lanterns. Will also fit 220, 275, 290, and 295.
Latch works great - has some scratches and a couple small dents - overall great condition (see photos)
This product is not included in the OCP free shipping program.
- New!
Smith-Victor Large Carry Case - CC15
Used Smith-Victor carry case for all large hat 228 style lanterns. Will also fit 220, 252, 275, 290, and 295.
Has some scratches, one edge is bent a little but doesn't hinder the case closing, both latches aren't perfect on latches tight but is a little bent, the other latch is loose but still closes.
This product is not included in the OCP free shipping program.
- New!
Guillotine 228 Carry Case - CC30
This is a used but newly re-done guillotine carry case. It does not have the decal, latches or rivets needed to put it together.
This product is not included in the OCP free shipping program.
- New!
Guillotine 220 Carry Case - CC31
This is a used but newly re-done guillotine carry case. It does not have the decal, latches or rivets needed to put it together.
- New!
Guillotine 228 Carry Case - CC32
This is a used but newly re-done guillotine carry case. It does not have the decal, latches or rivets needed to put it together. This one has a couple scratches from being moved around from place to place.
This product is not included in the OCP free shipping program.
- New!
Generator Lantern, Reproduction - R204
Reproduction generator for 220, 228, 275, and similar Sears lanterns. New generator includes new gas tip, spring, and tip cleaning wire.
- New!
Ventilator 339, Used - F150
This ventilator is used. It will fit Canadian models 339, 335, 321A, 321B, 321C, 325, and 325A.
- New!
GPA Starter Toolbox Kit - K22
Here is a kit of the most commonly used parts when repairing most lanterns and stoves. Buying kits saves in overall cost and comes with free shipping anywhere in the USA.
- 4 new Coleman check valves
- 10 Leather pump cups - pre-oiled
- 5 Neoprene rubber pump cups
- 10 Large valve stem packings for 1/4"
- 5 Small valve stem packings for 3/16"
- 10 Generator tube packings
- 10 One-piece fuel cap gaskets
- 10 Three-piece fuel cap gaskets
- 10 Cap gaskets sized for the 242 or 500 stoves
- 20 Peerless Mantles with Thorium 21A size for most double and single mantle lanterns
228 Vent, Old Style Used - U867
This is an early style 228 ventilator. This vent has a couple paint chips and small white dots that might come out but is otherwise in great condition (see photos)
Fount 220/228, Old Style, 12-62 - U891
This is a used old style fount for the 220/228B through 220/228F lanterns. It is dated 12-62.
Has paint chipping and some rust (see photos)
220 Frosted Batman Globe - G301
New frosted Batman globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
Also known as part number 2000026613.
Generator Spring, New Style, Used - S106
Used generator spring for 200, 220, 228, 242, and 275 lanterns. Also fits some Sears models. This is the newer style.
Will show signs of use but will be in good shape.
Air Intake Tube Old Steel - E1138
This is a old timey steel tube made back in WWII and would have been used on the 220C model lanterns.
220 Red Logo Pyrex Globe USA - G28
This is a US made original globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. These are used globes but in very nice shape.
Globe 220 White Logo USA Replacement - G127
Made in USA 220 white logo replacement.
This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
220 Peerless Globe - G130
This is a Peerless Japan made globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
220 No Letter Globe - G179
Used no letter globe. This fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
220 Globe Sears Logo - G59
This is an original used globe for the Coleman made Sears lanterns made from 1963 to approximately 1970. Although used, it has been inspected for damage or defects. This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
Mica Globe Panels - E1120
These mica panels are 3" x 5" in size.
General information:
- Mica can be cut with sharp scissors or a good paper cutter
- This is the only size that is available
- Mica is a natural product that is mined from the earth and will have slight variations in clarity, thickness, lines and light scratches.
- Mica is not available in amber or red.
- Mica can withstand temperatures up to 1800 degrees F.
- These are only sold in a package of 5 panels.
Valve Stem Retaining Ring - 1/4" - S04
This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.
Filler Cap, Black, Used - E1041
This is a used one piece filler cap. Paint is chipped or missing. Comes with a new gasket that you will have to install.
Filler Cap Steel, Used - E1386
Used steel filler cap for Coleman lanterns. All will vary in wear.
Comes with a new gasket that you will have to install.
Filler Cap Nickel, Used - E1395
Used nickel plated one piece cap. Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.
Wear and finish will vary.
Comes with a new gasket that you will have to install.
Fount 220/228, Old Style, 2/62, Used - U890
This is a used old style fount for the 220/228B through 220/228F lanterns.
Has small scratches/scuffs, chips and looks like some plastic got melted to the outside but might be able to get it off (see photos).
Filler Cap Dark Green Used - E1431
This is a used one-piece filler cap that is the darker green used on 288 and similar lanterns. Paint may be chipped or scratched; each one will vary in wear. Comes with one new gasket for you to install if needed.
Mixing Chamber, Old Style, Used - E1185
This is a used older style brass mixing chamber for the 220-228 series lanterns.
228 Vent, Old Style Used - U865
This is a used vent for models 227 and 228B through 228E. Very nice vent. Has a small dent/rust where the ball nut sits (see photos).
Pump Assembly Leather Used Square Nut - U810
This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
Filler Cap Gray Used - E1141
This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.
Filler Cap Brass Used - E1307
This is a used one piece brass filler cap. Wear will vary.
Comes with a new gasket that you will have to install.
Filler Cap, Assorted, Used - E1114
Used filler cap that will fit most lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps.
These are all assorted colors that have missing paint, are tarnished or have been repainted and do not match the original color - photo is for illustration purposes only - comes with one filler cap and new gasket you will have to install.
Filler Cap Brown Used - E1026
This is a used one piece filler cap from a 275 lantern. Paint may be chipped or missing in some spots - wear will vary. Comes with a new gasket that you will have to install.
Burner Cap 220 Brass Round, NOS - E1044
NOS burner Cap 220 Brass. Fits most models of double mantle lanterns and lamps. For nickel plated caps see part 112-3231.
NOS Burner Cap 220 Nickel Round - E1631
New nickel plated brass burner caps with round head. Fits most models of double mantle lantern and lamps.
Plastic Funnel Small - R702
This is a new plastic filler funnel. Small and easy to pack. Works well for standard sized filler caps. Also, the funnel tip just fits inside the smaller style caps like on the 242, 243 and some 500 stoves.
Mantle String Tie #21 4 Pack - M02
Coleman's Most Popular Sized Mantles. 4 mantles per pack.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
Also known as part number 3000004344.
220 Globe, Pyrex Green Sunrise Logo - G24
This is an original used green sunrise logo globe made between 1946 and 1959. Although used, it has been inspected for damage or defects.
The light green logo is very light as was common. The back has "PYREX" over "MADE IN USA"
This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. Some of the markings are very light and hard to see.
220 Frosted Sunrise Globe - G300
New frosted sunrise logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
Also known as part number 2000026613.
220 Half Frosted Globe - G302
New half frosted globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
Also known as part number 2000026613.
228 Vent, Old Style Used - U866
This is a used vent for models 227 and 228B through 228E. Very nice. Has a couple small paint chips (see photos).
Fount 220/228, Old Style, Used - U892
This is a used old style fount for the 220/228B through 220/228F lanterns. It is dated 12-65.
Has paint chipping and a couple scratches/scuffs (see photos)
Filler Cap 3 Piece AGM Used - E1634
Used AGM Cap. Has a steel screw and new filler cap gasket. This filler cap has the AGM hole in top. Shows signs of wear. Could be any combination of the following; wrench marks, oxidization, or fading.