228E

Used valve wheel for many of the Coleman made Sears single and double mantle lanterns.

This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap. 

If your filler cap is a standard size and has a bolt in the center then these gaskets will work. 

Red 3 piece filler cap shown for demonstration purposes only.

Used Gas tip.

This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date. These are the updated design that uses a smaller head on the air stem. You won't need your current air stem any more as this comes with a new one that is updated and replaces your old one. 

 If your part diagram calls for the 242B5381 or a 621-5361 check valve, then this would be the correct part. It is also known as part number 2006381ZCL.

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

No Border Logo with "Reg." & "Lantern" for 1961  to 1964 200A, 220 & 228 E & F Lanterns

Most Popular Sized Mantles. 4 mantles per pack. Use on these lanterns models: 200, 200A 201, 214, 220, 228, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960. Also all Coleman Lamps. These Peerless mantles are the same size as the Coleman 21A mantles. Made in India.

These Peerless mantles work well on single mantle lanterns. Made in India. They are the same size as the Coleman 99 mantles. A little bigger than the 2C-HG mantles but not as big as the 111 mantles. 2 per pack.

Burner screen for the model 220 and 228 lanterns. Fits most double mantle lanterns and lamps with small burner caps.

This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.

Also known as part number 425A1361

Graphite ribbon. It is 1/4 inch wide and 12 inches long. It is scalloped to make it more flexible for wrapping. Works for tip cleaner assemblies or any other thing where the normal graphite packing won't fit. It is easily cut with a pair of scissors to fit whatever you might need.

This is the common Coleman pump cup that fits most lanterns and stoves. 

Has a 7/8 inch diameter and is made in the USA of oiled leather.

Shorter burner tube for the model 220 slant lantern. Same as the normal 101-324 burner tube only a little shorter. Measures 2 1/4 inches long. Many of the slant 220 and 228 lanterns took shorter burner tubes.

Aftermarket product that claimed to convert your lantern to be able to run unleaded gas. It attaches to the generator. Was made to fit 286, 288, 220, 228, and 275 lanterns. It should fit a 200A too. I have never tried one and don't quite understand it but it is a neat addition to a collection.

Reproduction burner tube that measures 2 1/2 inches long. Some early lanterns and lamps took this size.

Push on nut for pump. The large push on nut is used with the neoprene pump cup.

Newer style mixing chamber for the model 220/228 lanterns. 

New steel fuel tube spring for the models 200, 200A, 202, 220 series, 228 series, and 242 series lanterns. Also for the 530 pocket stove and most likely many others. Overall measures 9/16" long, OD of 3/16" and an ID of approximately 1/8".

This is the cardboard tube that goes inside of the 200A and 220 size generators, and many others.

Steel burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long. These are the older style gray looking steel tubes as used on lanterns and lamps made during the war years.

Used valve wheel screw.  Will be in good condition. These will not fit the 236 or 237.

Mixing chamber for lamps and lanterns. It has the burner tube holes at a wider spacing than the normal mixing chambers. The burner tube holes are 1/1/2 inches apart center to center. Normal mixing chambers are spaced 1 3/8.

Valve stem nut for 220, 228, 275 Lanterns. Also fits the M1942 Stove. May fit others.

German made white logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

Used made in Mexico white letter globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

Used red sunrise globe used on Canadian lanterns. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

This is the smaller sheet metal style screw used on the 202, 220/228D, 220/228E, and early 200A lanterns. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.

Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 3/4 inches long.

New Old Stock parts. Comes with original box.

This is a one piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.

Comes with a new gasket that you will have to install.

This is an original used green sunrise logo globe made between 1946 and 1959. Although used, it has been inspected for damage or defects. 

The light green logo is very light as was common. The back has "PYREX" over "MADE IN USA"

This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. Some of the markings are very light and hard to see.

Used reflector with pistol grip for the model 220 and 228 B-F lanterns. Really good shape and solid. This hooks onto the post of the burner frame - top and bottom. See photos. Lantern not included.

Used Eccentric Block for the 220 & 228 lanterns up through model F. Will not fit H, J, or K.

This is a used one piece filler cap from a 275 lantern. Paint may be chipped or missing in some spots - wear will vary. Comes with a new gasket that you will have to install.

Used direction disk for the earlier double mantle lanterns such as 220/228B, C, D, E, and F. Will show signs of wear but still be in good condition. May be a transition disk between the 70's & 80's model lanterns.

Used AGM Cap. Has a steel screw and new filler cap gasket. This filler cap has the AGM hole in top.  Shows signs of wear. Could be any combination of the following; wrench marks, oxidization, or fading.

This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

New Filter Funnel For Lamps And Stoves. 

Stops filling your lantern or stove at the correct level.

This is a used burner assembly that will fit models 220/228B through 220/228E. It will show signs of use but will be in good condition. Has the long vent rod for the taller vents. If you change the vent rod to a shorter one, (HERE) it would work fine for a 220F.

Used needle assembly for the 220E5891 generator. Will show signs of discoloration from being used, but will have a good needle. Used in all 220 and 228 model lanterns except for the slant valve models. Also used in lamps 118B, 132A, 133, & 143. Sears models 476.72213, 476.72212, & 476.74070.

Used pump assembly with plastic cap, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup. 

Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. 

These simply slide on and you cross the wires instead of tying strings - very quick to install.

Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Zippo brand Flints for the Coleman Lantern Spark Igniter.

Single Ball Nut. Fits all Coleman lanterns except the 242 type models.

This is a used one piece filler cap. Paint is chipped or missing. Comes with a new gasket that you will have to install.

Used steel filler cap for Coleman lanterns. All will vary in wear.

Comes with a new gasket that you will have to install.

Used nickel plated one piece cap. Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.

Wear and finish will vary. 

Comes with a new gasket that you will have to install.

Used Needle for the fuel and air tube inside the fount. Used on 220 and 228 series lanterns up thru model F and the 118B lamp.

NOS Jamb Nut for all the model 200, 242, 243, 220, and 228 models. Came from an old parts bin in a Coleman service center.