242

This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date. These are the updated design that uses a smaller head on the air stem. You won't need your current air stem any more as this comes with a new one that is updated and replaces your old one. 

 If your part diagram calls for the 242B5381 or a 621-5361 check valve, then this would be the correct part. It is also known as part number 2006381ZCL.

This small gasket is for the model 242, 242A, 242B, 242C, 243, 243A, 234, 234A, 247, 249 and other similar lanterns and lamps that take the smaller filler cap. 

Also fits the model 500 stove and the early 520 stoves. The green filler cap is shown for identification purposes only and is not included.

Most Popular Sized Mantles. 4 mantles per pack. Use on these lanterns models: 200, 200A 201, 214, 220, 228, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960. Also all Coleman Lamps. These Peerless mantles are the same size as the Coleman 21A mantles. Made in India.

These Peerless mantles work well on single mantle lanterns. Made in India. They are the same size as the Coleman 99 mantles. A little bigger than the 2C-HG mantles but not as big as the 111 mantles. 2 per pack.

Graphite ribbon. It is 1/4 inch wide and 12 inches long. It is scalloped to make it more flexible for wrapping. Works for tip cleaner assemblies or any other thing where the normal graphite packing won't fit. It is easily cut with a pair of scissors to fit whatever you might need.

This is the common Coleman pump cup that fits most lanterns and stoves. 

Has a 7/8 inch diameter and is made in the USA of oiled leather.

Coleman's Most Popular Sized Mantles. 2 mantles per pack. 

Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Also known as part number 3000004345.

Reproduction gas tip for 200A5891 generator. Also works well for using on the 220 generators to do a kerosene conversion.

Eccentric Block for 200, 200A, All 242s, 201, 202, 243, 234, 335, 339 and 247. Also Sears 476.74550 & 476.72211.

Valve stem nut for the model 214, 242 and 200 series lanterns.

Coleman's Most Popular Sized Mantles. 4 mantles per pack. 

Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Also known as part number 3000004344.

This fits models 200, 202, 200A,242, 242A, 242B, 242C, 247, 249. and 5101.

This is a new Coleman made burner cap for the the 200, 200A, 202, 243, 242  and 247 lanterns. Also fits a few lamps and Sears lanterns.
Also known as part number 2423231.

New Coleman made Spark Igniter. Comes in new packaging with instructions.

Reproduction check valve for 242, 242A, 242K, 243 and 243A lanterns. This is the re-buildable type check valve for early single mantle lanterns that did not use an air stem. Will not work with others.

This ventilator is used. It will fit Canadian models 339, 335, 321A, 321B, 321C, 325, and 325A.

Reproduction needle assembly for the 200A2891 T66 generator used on models 121, 200, 200A, 202, 242, 242B, 242C, 476.72211, 476.74550

This replacement screen will fit the burner caps used on 242 and 200/200A model lanterns.

This is a used Burner frame for the 242A through C lantern. Will also work on the 247 and other similar lanterns. 

Is stamped with 3000.

These are original old stock Coleman made in the USA amber globes. They have the blue line on the top and bottom edge as was common on these. Probably from the late 70's or early 80's. Very limited supply. Used on lanterns from 1960 to 1980. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249.

Filler cap insert for the models 242, 242A, 242B, 242C, 243, 243A, 234, 234A, 247, 249 and other similar lanterns and lamps that take the smaller filler cap.  Also fits the model 500 stove. Will have a new gasket installed.

Used generator nut for all the model 200, 242, 243, 220, and 228 models. It is in fine shape, just dirty.

New filler cap screw for the small 242 & 249 lanterns and 500 stove size filler caps.

This is a used Burner frame for the 242A through C lantern. Will also work on the 247. 

Is stamped with 3000.

This is the small, beveled bushing that goes on the valve stem below the graphite packing on the 200, 200A, 202, 242, and 243 lanterns, along with many stoves that have a 1/4" valve shaft. 

Reproduction nickel plated vent rod for the models 234, 242A, 242B, 242C, 247, 249, and similar style lanterns. Will not fit the Australian made 249 lantern.

This is a used globe for an AGM lantern. Marked heat resisting. The writing is faint as was common on these. These will also fit on 200a lanterns.

New steel fuel tube spring for the models 200, 200A, 202, 220 series, 228 series, and 242 series lanterns. Also for the 530 pocket stove and most likely many others. Overall measures 9/16" long, OD of 3/16" and an ID of approximately 1/8".

This is the cardboard tube that goes inside of the 200A and 220 size generators, and many others.

Reproduction valve stem nut for the model 200A lantern. Also fits the 202, 242, 243, and 247 series lanterns and also the 425F and G stoves. Does not come with the new packing.

Used brass filler cap. Will all vary in wear and amount of brass faded. Fits the model 242, 242A, 242B, 242C, 242K, 243, 243A, 247, 249 lanterns and the model 500 stove.

Will come with a new gasket for you to install if needed.

Reproduction tip cleaner assembly for the model 200, 200A, 201, 202, 242, 247, 335 and similar lanterns. Also fits the 523 and the 520/M1941 stove.

This is a new old stock Trailblazer globe. These are not Coleman globes but are the same size and were made in the USA about 20 to 30 years ago. Comes with the red trailblazer logo. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, 247, and 249.

New rubber pip for the re-buildable NRV type check valve used on the 242, 242A, and the M1950 stove.

New Old Stock parts. Comes with original box.

These are original Coleman made in the USA amber globes. Some will have the blue line on the top and bottom edge as was common on these. Most likely made during 1960. Used on lanterns from 1960 to 1980. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249. "Made in U.S.A." on globe.

Has a few imperfections in the glass, color is faded and has one burn mark (see photos)

New reproduction pump cup assembly for 242 NL (No Letter), 242A , 242K, 243 , 246 and or any Coleman lantern or stove from the early 30's with a solid pump stem with no air hole in the middle. These are made for the USA manufactured Coleman pump shafts and will fit as they should. If yours is made in Canada, you will have to use a small file to widen the brass center to a cone shape to match your pump shaft - see the photos. Also known as part number 233-518

This is a used fount for the model 242 Lantern. It is date stamped 4-47. Has some paint chipping and a couple very small dents. The sunshine logo looks faded but is there.

It will work for models 242, 242A, 242B, 242C, 243, 243A, 247, and 242K.

This is a used brass nickel plated fount for the model 242C. It is date stamped 9-47. It will also work for models 242, 242A, 242B, 243, 243A, 247, and 242K. Has a small dent but otherwise in very nice condition - still has most of the nickel plating finish (see photos)

Brass bolt for 242 or 242NL Lantern - will not fit other versions of the 242. This is just for the top brass bolt.

New burner cap for the model 242 series lanterns. Also fits the 200, 200A, 202, 243, and 247 lanterns.

Solid brass with stainless steel screen.

Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. 

These simply slide on and you cross the wires instead of tying strings - very quick to install.

Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Stainless Steel burner frame to valve nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.

Need the washers for under a 200 or 200A frame? Look HERE.

Zippo brand Flints for the Coleman Lantern Spark Igniter.

These come in a pair of 2. They are new stainless steel washers that go under the burner frame on all 200 and 242 lanterns. Identical size as the originals.

New 200 burner frame Pal Nut is HERE.

New 200 burner frame Nut is HERE.

NOS Jamb Nut for all the model 200, 242, 243, 220, and 228 models. Came from an old parts bin in a Coleman service center.

This is a reproduction mica globe for the smaller single mantle lanterns. This will fit on the 200, 200A, 234, 243, 241, 242, 246, 247, and 249 lanterns. It will also fit on any lantern that would take a 440 size globe. It is 4 1/4 inches tall and has a diameter of 3 1/2 inches. The craftsmanship is nice and it is like the old mica globes that went into the first lanterns. Mica is a mineral. It may have variations in clarity, small spots, light scratches or other natural discolorations.

Reproduction spring for the fuel tube spring on the model 200, 200A, 202, 220 series, 228 series, and 242 series lanterns. Also for the 530 pocket stove and most likely many others. Overall measures 9/16" long, OD of 5/32" and an ID of approximately 1/8".

Used generator spring for 200, 220, 228, 242, and 275 lanterns. Also fits some Sears models. This is the newer style.

Will show signs of use but will be in good shape.