288A

Nut used for the top of the valve on 214, 286, 288 and 290 models. May have other applications also.

This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves.

Has a 7/8 inch diameter and is made in the USA of oiled leather.

NOS metal pump cap for pump assembly. Does not come with whole assembly - just the top exterior metal cap is included.

This is a used pump square nut.

Comes with one square nut ONLY.

This tool has both a wide and slim slot for almost all check valves and makes changing check valves very easy - will only take a few minutes if used properly.

C001 Check Valve: This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date.  
R425 Check Valve: This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves. 

This is a one piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.

Comes with a new gasket that you will have to install.

This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.

Used Pump Assembly Spring

Spring ONLY

This is a new 8 oz. gas bottle used to fill gas lanterns, stoves and lanterns.

Used nickel plated one piece cap. Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.

Wear and finish will vary. 

Comes with a new gasket that you will have to install.

Used knob for the 282, 285, 286, 288, 290, 295, 295A and 639 lanterns. May fit others also.

Used pump assembly for most stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup. 

Used pump assembly with plastic cap, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup. 

Burner Assembly for the model 288 lanterns. The burner tubes are steel. Will vary in wear.

This is a used one piece brass filler cap. Wear will vary. 

Comes with a new gasket that you will have to install.

This is a used one-piece filler cap that is the darker green used on 288 and similar lanterns. Paint may be chipped or scratched; each one will vary in wear. Comes with one new gasket for you to install if needed.

Used collar for the model 288A lantern.

Used collar for the model 286A or 288A lantern. Marked for both models.

This is a new, reproduction 3 piece cap. Excellent craftsmanship. This is not the type with a hole in the side.

This is a new plastic filler funnel. Small and easy to pack. Works well for standard sized filler caps. Also, the funnel tip just fits inside the smaller style caps like on the 242, 243 and some 500 stoves.

This is a used one piece filler cap from a 275 lantern. Paint may be chipped or missing in some spots - wear will vary. Comes with a new gasket that you will have to install.

Used AGM Cap. Has a steel screw and new filler cap gasket. This filler cap has the AGM hole in top.  Shows signs of wear. Could be any combination of the following; wrench marks, oxidization, or fading.

This is a used collar for the early 288 lantern. Has the black circle around the opening rather than the red.

Used nickel plated one piece cap. All will vary in wear.

Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.  

Comes with a new gasket that you will have to install.

Generator nut for the model 214, 222, 229, 286, 288 290, 635 and 639 lanterns.

Used closed ball nut.

It is approximately 4 3/8 inches tall and has a 4 1/4 inch diameter. This original globe fits models 214, 214A, 214B, 214C, 282, 282A, 288, 288A, 288B, 286, 286A, 286B, 321, 335, 5150, 5151, 5152, 5153, 5154, 5155, 5158, 5159, and 5417. Made in the USA. This globe is used.

Used Burner Assembly for the model 288A lanterns.

Used steel filler cap for Coleman lanterns. All will vary in wear.

Comes with a new gasket that you will have to install.

This is a used one piece filler cap. Paint is chipped or missing. Comes with a new gasket that you will have to install.

Used filler cap that will fit most lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps. 

These are all assorted colors that have missing paint, are tarnished or have been repainted and do not match the original color - photo is for illustration purposes only - comes with one filler cap and new gasket you will have to install.

Here is a kit of the most commonly used parts when repairing most lanterns and stoves. Buying kits saves in overall cost and comes with free shipping anywhere in the USA.

• 4 new Coleman check valves
• 10 Leather pump cups - pre-oiled
• 5 Neoprene rubber pump cups
• 10 Large valve stem packings for 1/4" 
• 5 Small valve stem packings for 3/16" 
• 10 Generator tube packings
• 10 One-piece fuel cap gaskets
• 10 Three-piece fuel cap gaskets
• 10 Cap gaskets sized for the 242 or 500 stoves
• 20 Peerless Mantles with Thorium 21A size for most double and single mantle lanterns

This is a used collar for the 288 lanterns with the red arrow.

Picket amber globe for the 288 size lantern. Has no manufacturer markings on it anywhere. It is approximately 4 3/8 inches tall and has a 4 1/4 inch diameter. This globe fits models 214, 214A, 214B, 214C, 282, 282A, 285, 288, 288A, 288B, 286, 286A, 286B, 321,325, 335, 5150, 5151 (A/B/C/D), 5154 (A/B), 5155 (A/B), 5159, 5417, 5419, 5428, & 5429.

This is a used one piece filler cap off the Model 200A burgundy. 

Comes with a new gasket that you will have to install.